coinco changer manual

Serial Number 1503005895 would indicate thatChanger is compatible with current vendingNote: All Global changers are equippedAs above with the additional ability toCashless devices whilst being connected to aThe changer model number is shown in theWhere. Pound.Page 3Specifications. The COINCO GLOBAL 2 coin changer hasTubes snap in and out of housing for easyPays out change from self-loading, highTwo motors provide fast, accurate payout. Programmable tube floats allow variableState-of-the-art electronic logic system isLightweight, rugged plastic construction. All models equipped with the MDB protocol. Lockable coin loading door allows easyBill validator or cashless system. After Unpacking. After unpacking the unit, inspect it for anyIf the unit is damaged, notify the shipping company immediately. Only the consignee (the person or companyWe recommendIf the coin changer is being stored or used as aPower Requirements (by model)Relative HumidityOperating Attitude. Height: BASE T O TOP OF COIN RETURN LEVERWidth: 138.9mm (5.47 inches). Depth: GATE OPENApproximately 7 pounds. Approximately 3.15 kilograms. Coin Size Range. Up to 32 coins or tokens in the size range ofPage 4Unplug ribbon cableFigure 3). Do not over tighten as this couldPlug the ribbon cable into the changer (see. Figure 2). Figure 1Figure 2Connector to the vending machine frame.Figure 5 for MDB. MDB master. Figure 8 for 4-Price ElectromechanicalConfiguration. Note: The vend prices are set on thePage 5Figure 3Tilting the coin tubeMake sure all coins lie flat and that eachPayout at least two coins from each tube toFigure 4. Note: Hand loading the tubes will not giveIf audit isPage 6Devices. E.g. KeyAudit device etc. Other MDB Slave. Devices. E.g. KeyAudit device etc.Peripheral). Comms Gnd. P1 - MDB Slave. ConnectorData Connector. Data ConnectorP2 - Protocol A Data. ConnectorPage 7Master TX. Master ReceiveP1 - Connector. Protocol A. DataA Data. Power. Connector. P3 - MDB Master.

• coinco coin changer manual, coinco changer manual, coinco 9370 s sr changer manual, coinco s75-9800b coin changer manual.

See why thousands are coming to eBid. Fri 11 Sep 2020 22:17 (EDT) Upgrade to SELLER for free and pay just 5% when you sell. Fancy zero fees for life. Figure 12 CLEARING COIN JAMS CAUTION: Excessive screwdriver pressure or twisting can cause permanent damage to the coin changer. Figure 13. Louis, MO 63124-2013 (314) 725-0100 or (800) 325-COIN. With enhanced security we require you to reset your password, click “Login” (below) and then “Forgot Password” once on that page. See the whole process here. The item includes accessories found with the original product and may include a warranty. See the seller's listing for full details and description. Of stel een vraag aan een andere bezitter van uw product als u problemen heeft met uw.Reload to refresh your session. Reload to refresh your session. For Your Records. 3. Features. 4. After Unpacking. 4. Specifications. 4Installation Diagrams. 7Option Switch Module. 10. Setting the Vend Price on a Single-Price Changer. 11. Setting the Vend Price on a Four-Price Changer. 12. Setting the Vend Price on a Protocol A Changer. 13. Setting the Cashless Vend Price on a Protocol A Changer. 13. Setting the Vend Price on MDB and BDV Changers. 14. Manual Fill Mode. 14. Float Mode. 14. Setting the Float Mode Levels. 15. Activating Float Pay-Down. 15. Setting The “Use Correct Change” Value. 16. Setting the Exact Change Accept Group. 16. Reading Audit Information. 18. Tube Counts. 18. Digital Display Address Chart. 19. Changing the Coin Tubes. 23. Changing Coin Routing. 23Cleaning. 25. Clearing Coin Jams. 26Diagnostics. 28. Troubleshooting Guide. 29Page 2For Your Records. This manual contains information on installing,The manual isA label indicating the coin changer modelRefer to the model andCoinco Service Centre for information orFor example.

Module” section of this manual).The LED and theExample: Switch 1, 3, 4, set to on and theIf the scaling factorThe current decimalNOTE: The vend price must be set to anMode” section of this manual).Display Mode.Note: The Display Mode will exit automaticallyPage 11A Four-Price Changer. The vend price on a four-price changer may beCorrect Change” light will stop flashing.The vend price can be set in single incrementsEXAMPLE: If the first, fourth and fifth priceEXAMPLE: If the lowest denomination coin isNOTE: If the price for one or more of theMode” section of this manual).Display Mode.Consult Hand-held Computer manufacturer.Module” section of this manual).Option Switch Module, press and release the. Mode Button (see Figure 2). The changer’s. Main Logic Board LED and the “Use Correct Change” light will begin to flash. Page 12A Protocol A Changer. The vend price on a Protocol A changer may beMode” section of this manual).Priceline 1)Display Mode.Mode” section of this manual).Display Mode.Cashless pricelines C201 to C225.Mode” section of this manual).Display Mode.Addresses C201-C225. When a vend is madeCash vends will still use the prices stored inMode” section of this manual).Display Mode.Page 13Changers. Float ModeSee vending machine manual for details.Manual Fill Mode. Manual Fill Mode allows coins to be insertedWhen high sensor level or float level is reachedEnter the Display Mode (see “Display Mode”When “FILL” appearsA (escape) is pressed. Manual Fill Mode is supported forSee vending machine manual for details. Float Mode is used to systematically reduce theStandard Float Mode, any coins normally routedThe coins will then beOnce a tube float level isPay-down” section of this manual). When in Manual Fill Mode, the acceptor willThe float pay-down level does notPage 14Levels. The Float Mode Levels for both Float Level and. Float Pay-down can be set in two ways:Address “A007”The individual tubeSetting All Four Float Levels At Once:Mode” section of this manual).

ConnectorSelection switchVend Line 1Vend Line 3. Vend Line 4. Blocker. Live. NeutralVend Relay. Typical Vending machine vend line wiring, Only to beP1- Jones Plug. Page 8The 800 Series changer is equipped with aDigital Display. Inventory Buttons. This Display Mode is used to read informationThe Display Mode may be entered by pressing. Inventory Buttons A and D simultaneously. InButton activation will be recognized only if longer than 0.5Mode, Inventory Buttons A through D are usedButton A. ESCAPE. Button B. INCREASE. Button C. ENTER. Button D. DECREASE. EXAMPLE: Simultaneously press A and D toInformation currently stored in non-volatileUse either Inventory. Buttons B or D to increase or decrease thePress Button C againPress A to return to the. Address Display. Press A again to exit the. Display Mode. You will exit the Display Mode if one of theMode is exited;Indicates Float Level Is Set On. At Least One Tube. Indicates At Least One Coin Is Enabled. Indicates (By A Flash) Each. Figure 10. NOTE: All addresses in the Display Mode canSupport Software (see separate Coinco SupportNOTE: If power is removed from the changerPage 9Located behind the acceptor on the middle rightThe first eight are usedPrice” section of this manual). The last four Option Switches are used to enableNote: The swiches are ON in the upwardsSwitch A (SW9). Controls whether the escrow feature of theOFF Escrow not inhibited. Switch B (SW10). Determines the operation mode of the changer.OFF Operates as a Single-Price changer. Switch C (SW11)Controls the vend holding feature.OFF Vend is pulsed. Switch D (SW12). Controls when the changer enters the “Use. Correct Change” condition.OFF Uses a programmable value forPage 10A Single-Price Changer. The vend price on a single-price changer maySwitch 1. Switch 2. Switch 3. Switch 4. Switch 5. Switch 6. Switch 7. Switch 8Figure 11. The vend price can be set in single incrementsEXAMPLE: If the lowest denomination coin isConsult Hand-held Computer manufacturer.

Total slugs rejected. Total value coins tube 1. Total value coins tube 2. Total value coins tube 3. Total value coins tube 4. Value card sales life. Value card credit life. Value card discount life. Total number of vends. Total value of coins routed to tubes. Total value of coins routed to cash box. Total value dispensed. Total value dispensed usingChange lost. Total value of all vends. Value of vends taken whenActual value of discount given. Value of vends from tokens. Value taken from prepaid cards. Count of vends for price 1. Count of vends for price 2. Count of vends for price 3. Count of vends for price 4. Count of vends for price 5. Count of vends for price 6. Count of vends for price 7. Count of vends for price 8. Count of vends for price 9. Count of vends for price 10. Count of number of invalid coins. Total coins in lowest value tube. Total coins in second lowest value tube. Total coins in second highest value tube. Total coins in highest value tube. Total value of coins. Total value in second lowest value tube. Total value in second highest value tube. Total value of coins in highest value tube. Value sales from prepaid period. Value credit to prepaid card. Value discounts during prepaid card usePage 19DescriptionPrices 2 (Repeated at address C102). Prices 3 (Repeated at address C103). Prices 4 (Repeated at address C104). Prices 5 (Repeated at address C105). Prices 6 (Repeated at address C106). Prices 7 (Repeated at address C107). Prices 8 (Repeated at address C108). Prices 9 (Repeated at address C109). Prices 10 (Repeated at address C110). Maximum change paid out in. Multivend mode. Discount award (Increase in creditDiscount Award Trigger. Exact Change Accept Group. Value. ValueExecutive (Protocol A). Coin Value reported - Coins up to and includingExact Change condition.Executive (Protocol A). Card Revaluation OFF:Card Revaluation ON:No Executive Card ReaderExecutive Card Reader InstalledValue. Programmable 4-20 secondsFour Price Time out. Page 20Field.

The far left digitThe far rightSetting Float Levels Individually:Mode” section of this manual).Use button B (increase) or button D (decrease) to reach the desired tube selection.The far right decimal point will illuminate indicating theDisplay.The Digital Display’s second decimal from theActivating Float Pay-Down. Pressing and releasing buttons A and B simultaneously activates Float Pay-down. Use Manual. Fill to replenish low tubes (see “Manual Fill. Mode” section of this manual). The Digital Display’s second decimal pointPage 15Change” Value. Setting The Exact Change. Accept Group. When a value is selected for turning on the “Use. Correct Change” light, the light is illuminatedTHAT value or any lesser value. By setting the Exact Change Group you areNOTE: Option switch D set to the ON positionSee “Option Switch. Module” section of this manual for informationThe “Use Correct Change” light can be programmed to come on in three ways:Consult Hand-held Computer manufacturer.Address “C032” of the Digital Display.Mode” section of this manual).Exact Change Setting is now programmed toPage 16. The Exact Change Group can be programmed inConsult Hand-held Computer manufacturer.Mode” section of this manual).Change group to be accepted.Note: Coins of the same value are reported asCoin Number 0 is theSelect the coinPage 17Tube Counts. By briefly depressing and releasing an inventoryBy reading Audit Information, you can gainMode” section of this manual).Address “d000”.Display.NOTE: Audit Information is “read only” it canNOTE: Free vends issued directly from thePage 18Field. DescriptionCash to tubes. Cash to cash box. Dispensed cash. Inventoried cashVend value. Exact changeDiscount value. Token value. Prepaid card value. Total vends for price 1. Total vends for price 2. Total vends for price 3. Total vends for price 4. Total vends for price 5. Total vends for price 6. Total vends for price 7. Total vends for price 8. Total vends for price 9. Total vends for price 10.

Set vend price (see “Setting the Vend. Price” sections of this manual. Coin Return Lever. Make sure changer is mountedAcceptor is dirty or foreignCheck to see that acceptor coinClean acceptor and removeIf still rejects good coins. If still rejects good coins. Replace changer’s mainReplace acceptor with goodReplace defective acceptor. Replace changer’s mainReplace changer’s mainNo Coin AcceptanceAccepts Coins But. CreditAcceptor. Page 29Go To Cashbox. Coin Routing. Check that coins are routed to tubes. See “Rerouting the Coins.”. Tube Sensor BoardCheck the sensor board for looseReplace tube sensor board. If coin still goes to cashbox, replaceReplace acceptor. If coin still goes to cashbox. Replace changer’s mainCoin tube gate is inRemove acceptor back coverReplace acceptor. Tube Sensor Board. Replace tube sensor board withReplace tube sensor board. If coins still go to tubes. Replace changer’s mainCoin return lever. Make sure changer is mountedAcceptor. Replace acceptor with goodReplace defective acceptor. Switch 9 is ON - escrow isUninhibit the escrow feature. Turn switch 9 OFF and pressPayout Motor. Make sure motor wires arePlug motor wires intoIf still no payout, replace motorReplace defectiveAccepted Coins Always. Go To Coin Tubes. Changer Credits Coins. But Does Not Escrow. No Payout. Page 30Assembly, Payout. Assembly, Acceptor. Logic Board. Board, Upper Tube Sense. Cover, Logic Board. Lens, Upper Tube Sense. Lens, Cashbox. Latch. PVC Foam. Bracket, Strain Relief. Label, Identification. Label, PatentLabel, Configuration. Tube, Inventory. Shim. Mirror, Tube A. Mirror, Tube C and D. Labels, Tube. Plug, Lg. Strain Relief (selective models). Plug, Sm. Strain Relief (selective models). Label, Warranty (selective models). Pad (selective models)Gear, Encoder. Cover, Gearbox. Base, Payout-Upper. Base Payout-Lower.

DescriptionCard Scale factor. Max. CreditPrice Hold and DisplayEnable DEX ClearAccept Group. MDB Bill Acceptor EscrowNumber of Active Price lines. Executive Audit Peripheral Device. EnableValue. ValueNotes are Accepted up to and Including This. ValueProgrammable 5-50ms. Programmable 1-25Machine Identification Number. Values Assigned To Any Tokens Accepted. Machine Location NumberThe Prices Lines areToken Values. ID104 - DEX Audit FieldPage 21AddressesOptions. Select Unit Configuration,Note: The reported currency will be that of the coinsUsed to select a standard payout configuration or forALT options are user programmable.Displays the coin valuesThe following can only be set in the factory:Relative acceptance Levels (1-10) for all 32 coin typesEach Digit Represents a Tube “A-B-C-D”Value used to scale all coins. ValueDecimal Point Value (read only). Remainder Enable. Applicable to Dual CurrencyPage 22To remove the coin tubes, remove the acceptorThe front cover willFour slots have been placed in the frontPlace a screw driverThese shims are color-coded and are fixed toShims are removed and replaced by sliding in or out of theNOTE: Do not reuse shims. Installation andThis address allows the user to change payoutThis feature onlyWhen address A002 is entered five payoutSelection isThe far rightThis will be evident if a valueTo program a coin to a tube, select the tube byIf value “e” is chosenPressing enter (button C) again will return to theFor correct operation the scaling factor shouldE.g. if the least value coin accepted is the GBPFloat modes will be turned off and coin countsPage 23Example of setting up userTo configure the coin tubes via the Digital. Display, follow these steps:Mode” section of this manual).The far right decimal point will illuminate toThe payout configuration has now been changed to:Coin Type 0 goes to Tube A. Coin Type 1 goes to Tube B. Coin Type 2 goes to Tube C. Coin Type 3 goes to Tube D. Remaining Coin Types 4-15 go to Cashbox.

BUT, Coin Type 6 is interchangeable with coin type 0 andPage 24. Coin Type 0 goes to Tube A and cashbox. Coin Type 1 goes to Tube B and cashbox. Coin Type 2 goes to Tube C and cashbox. Coin Type 3 goes to Tube D and cashbox. Coin Type 6 goes to Tube A and cashbox. Coin Types 4,5 and 7-15 go to Cashbox onlyCleaning. Routine maintenance will improve performanceFrequency of maintenance will depend on environment and numberHowever, in harsh environments with lots ofThe coin changer should be kept in its originalThis will keepFigure 12Since all coins share a common coin ramp,For detailed cleaning of the acceptor, removeDue to its smallPage 25Modular assembly replacement provides theThese modulesUnplug ribbon cable from changer. Free lowerClearing Coin Jams. Should a coin jam occur in the cashbox chuteRemove recessed screw that securesPage 26If any of the errors listed below as “E001-E007”If a single error isIf there is moreThe error codes listed below are displayed uponThe following errors will require the changer toPage 27When the coin return lever is depressed or aThe Following Values In The Following Positions. Indicate a Response to the Coin that was Just. Dropped (the digit “2” is used for example purposesIs ON. Coin Type Recognized and CreditedLeast One TubeIndicates Left Cashbox Sensor Is BlockedIndicate the Condition in the Corresponding Tube:Page 28. Coin Type Not RecognizedFigure 13Lower Sensor Is Blocked. Lower and Upper Sensors Are Blocked. Tube Is Jammed. Sensor ErrorAn attempt has been made to route, howeverRejected as coin has been disabled by theRejected as the coin set associated with thisFigure 15No power. Make sure changerPlug changer intoAcceptorIf LED is on, replace acceptor. Replace acceptor. If still no coin acceptance. Replace changer’sIf still no coin acceptance. Replace changer’sIf LED is off, check to seeIf still no coin acceptance. Replace changer’sLow Power. Flashes “20” on display when coinCheck power source. Vend price is set to 0.

coinco ba30 manual

JCM UBA -Part 2 Source Link JCM UBA -Part 3 July 30, 2016 Bill Acceptor Repair And Cleaning With Washing Method. JCM UBA -Part 3 Source Link Replacing defective dollar bill changer. Source Link. You are buying a copy of a Coinco BA32R Bill Acceptor Operation and Service Manual. You will be sent by mail 28 page manual. This manual covers the following; 1. General Information 2. Installation 3. Operation 4. Maintenance 5. Trouble Shooting 6. Accessories 7. Parts List Any questions please call.Super high amount of views. 1 sold, 97 available. More Super high amount of views. 1 sold, 97 available. You are the light of the world. If you can't find the manual for the specific model you are searching for please let us know and we will do our best to find it for you. When you need parts and repair manuals to fix broken Coinco devices, we have exactly what you need at ServiceManuals.net. We will provide you with the information required to repair the malfunctioning equipment so that you or your customers can start enjoying your Coinco electronic device once again. If appears, then the manual is available for immediate download and you will receive the information right after placing your order We will then attempt to locate the service manual for you and in most cases get back to you within 24 hours. Please try again.Please try again.Please contact Seller for more detailed pictures in the event of an unclear image.In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Full content visible, double tap to read brief content. Please try your search again later.To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon.

• coinco ba30 manual, coinco ba30b manual, coinco ba30 manual, coinco ba30b manual, coinco ba30 manuals, coinco ba30 manual download, coinco ba30 manual free, coinco ba30 manual instructions, coinco ba30 manual online, coinco ba30 manual transmission, coinco ba30 manual user, coinco ba30 manual diagram.

The item includes accessories found with the original product and may include a warranty. See the seller's listing for full details and description. It still takes coins, but will not accept bills. Can anyone give me any advice. Thanks, KevinIf you have sufficient coins in your nickle tube then it's probably time to get it rebuiltmLooking up your number of flashes it indicates that the “left position sensor” is what is giving you problems.If you have sufficient coins in your nickle tube then it's probably time to get it rebuiltmThis is one of the worst validators ever made. Scrap it and buy a 2512It still takes coins, but will not accept bills. Can anyone give me any advice. Thanks, KevinAny comments on the Mag50. I only ask because it is a direct replacement (117v vs 24v on the 2512). I don't want to get in over my expertise level which is admittedly very low.Any comments on the Mag50. I only ask because it is a direct replacement (117v vs 24v on the 2512). I don't want to get in over my expertise level which is admittedly very low.The bad ones break down constantly. Mars tend to either rarely need to be repaired or they need repaired maybe every 3 years or so on average.Any comments on the Mag50. I only ask because it is a direct replacement (117v vs 24v on the 2512). I don't want to get in over my expertise level which is admittedly very low.It's easy! Sign in here. Ship validators to: How do I pay? I mistakenly bought 2. Can you please fix to one so I can pay. I am shipping thus today. Thank you. I already shipped item to you. Thanks I purchased from you because of your reputation. Im not sure what happened here. Thanks anyway. Please upgrade your browser to improve your experience. Vending Manuals This is a very brief walk through of trouble shooting your coinco ba bill acceptor.JCM UBA -Part 2 July 30, 2016 Bill Acceptor Repair And Cleaning With Washing Method.

It also analyzes reviews to verify trustworthiness. Please try again later. Nick 1.0 out of 5 stars But was a giant waste of time. Product did no workThe guy that rebuilt the validator left his number for help and advice. He was easy to get ahold of and very informative.In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Parasite Management for Horse Sheep Cattle.FECRT Reference Guide Incl.

coinco ba30b bill acceptor manual

10 Success Secrets Of Vending Business Professionals Enter your email address below and you’ll get access to 10 videos on how to start and operate a vending business. This iframe contains the logic required to handle Ajax powered Gravity Forms. ? Call Us (800) 713-6217 (770) 482-7993. Something went wrong. View cart for details. User Agreement, Privacy, Cookies and AdChoice Norton Secured - powered by Verisign. Angebote Hilfe Verkaufen Beobachtungsliste Beobachtungsliste einblenden Laden. Es ist ein Problem aufgetreten.Mehr zum Thema - Wird in einem neuen Fenster oder Reiter geoffnet Angaben ohne Gewahr. Der Betrag kann sich bis zum Zahlungstermin andern. Weitere Informationen finden Sie in den Nutzungsbedingungen fur das Programm zum weltweiten Versand - wird in neuem Fenster oder Tab geoffnet Angaben ohne Gewahr. Fur Kaufer mit Wohnsitz in einem EU-Mitgliedsstaat au?er Gro?britannien ist die Importsteuer nicht erstattungsfahig. Weitere Informationen finden Sie in den Nutzungsbedingungen fur das Programm zum weltweiten Versand - wird in neuem Fenster oder Tab geoffnet Mehr zum Thema - wird in neuem Fenster oder Tab geoffnet Mehr zum Thema - wird in neuem Fenster oder Tab geoffnet Mehr zum Thema - wird in neuem Fenster oder Tab geoffnet Mehr zum Thema - wird in neuem Fenster oder Tab geoffnet Mehr zum Thema - wird in neuem Fenster oder Tab geoffnet Ein Artikel mit Abnutzungsspuren, aber in gutem Zustand und vollkommen funktionsfahig. Bei dem Artikel handelt es sich unter Umstanden um ein Vorfuhrmodell oder um einen Artikel, der an den Verkaufer nach Gebrauch zuruckgegeben wurde. Weitere Einzelheiten, z. B. genaue Beschreibung etwaiger Fehler oder Mangel im Angebot des Verkaufers. Kontaktieren Sie den Verkaufer - wird in neuem Fenster oder Tab geoffnet und fragen Sie den Versand an Ihren Standort an. Bitte geben Sie eine gultige Postleitzahl ein. Bitte geben Sie eine Nummer ein, die kleiner oder gleich 49 ist.

• coinco ba30b bill acceptor manual, coinco ba30b bill acceptor manual, coinco ba30b bill acceptor manual pdf, coinco ba30b bill acceptor manuals, coinco ba30b bill acceptor manual download, coinco ba30b bill acceptor manual online, coinco ba30b bill acceptor manual.

Please try again.Please try again.Please contact Seller for more detailed pictures in the event of an unclear image.In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Register a free business account Please try your search again later.To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. Please try again later. Nick 1.0 out of 5 stars But was a giant waste of time. Product did no workThe guy that rebuilt the validator left his number for help and advice. He was easy to get ahold of and very informative. Please upgrade your browser to improve your experience. Vending Manuals This is a very brief walk through of trouble shooting your coinco ba bill acceptor.JCM UBA -Part 2 July 30, 2016 Bill Acceptor Repair And Cleaning With Washing Method. JCM UBA -Part 2 Source Link JCM UBA -Part 3 July 30, 2016 Bill Acceptor Repair And Cleaning With Washing Method. JCM UBA -Part 3 Source Link Replacing defective dollar bill changer. Source Link. The item includes accessories found with the original product and may include a warranty. See the seller's listing for full details and description. Super high amount of views. 5 sold, 13 available. More Super high amount of views. 5 sold, 13 available. You are the light of the world. New To The Vending Business. Yes, I am new to the Vending Business. No, I currently operate Vending Equipment. Our vending consultants are happy to answer any questions or concerns you may have. Leave this field empty if you're human: Contact Us 7144 Maddox Rd. All Rights Reserved. This iframe contains the logic required to handle Ajax powered Gravity Forms. ?

The problem is pretty consistent and I have only been able to clear the problem by manually and gently pushing the Stacker Plate back to the home position. But then the same problem will happen from the beginning with the next dollar bill. This type of error can not be repaired in the field. There are a few possible causes that will be addressed in a complete rebuild. I'm having a problem with the Stacker. But then the same problem will happen from the beginning with the next dollar bill. We do not need your old unit back.Please help. Trouble Shooting. Coinco BA30B bill validator not accepting. Coinco BA30B bill acceptor wont accept. First thing to do when trouble shooting this bill validator is to check the flash codes on the back of the remote box on the side of the validator. If the light is solid red the validator thinks its working properly. The following is the Diagnostic error codes for this unit.When trying to fix a non working bill acceptor. Start by taking the bill box off and the bottom deck out. Then blow out the entire unit with an air compressor. Then clean the sensors with a damp cloth. There are two sets of sensors one on the bottom deck you removed and one set inside the deck housing on the upper side. Portland, Oregon 97203. Book Vending Machines All Over the US First Steps in Buying a Vending Machine How to Adjust your Thermostat How to Change your Vending Machine Prices How to Clean your Dollar Bill Acceptor How to Load your Vending Machine How to Refill your Coin Mechanism How to Unlock your Vending Machine How to Clean a Soda Machine To use it, simply place your order and you will be able to choose store credit as the payment method when it comes time to pay for your order. We will get back to you in 24 hours. Thank you. Close Feedback Found a bug. Suggestions Copyright Need help. Business Development General inquiry Email address (optional): A message is required Message (required).

I have no experience in vending machines until recently, and this thing was an easy install. It works great, looks great, and was the best price for this item on ebay. The package was well packed and came fast. I would definately recommend this to anyone. This was an exact match and was an easy change out. Alle Rechte vorbehalten. The machine won't take money of there is no product to vend, and won;t take bills if it cannot pay out change. The machine won't take money of there is no product to vend, and won;t take bills if it cannot pay out change. I would guess that since the machine was empty and the coin mech is to be shut down as well it probably would go right into shut down and not just inhibit, so no the motor probably won't cycle. I would guess that since the machine was empty and the coin mech is to be shut down as well it probably would go right into shut down and not just inhibit, so no the motor probably won't cycle. It's easy! Sign in here. The bill path should have solid glowing red lights ( blinking red indicates error state, refer to Bill Acceptor Error Codes ). The Bill Acceptor Dip Switches are located under the black cover on the left side of the Acceptor. A screw must be loosened to remove this cover. The small switches are in a line numbering 1 through 8. Several functions may not work. Please re-enable javascript to access full functionality. I'm having a problem with the Stacker. It will accept and stack the first dollar bill just fine. But the Stacker Plate will not end it's cycle at the proper home position. It will push the first bill in, return to it's home position and push a second time. When pushing the second time, the plate will then stop mid-way through it's second push when the plate is at its fullest extended point and stop there. The next bill inserted (which it still will accept bills) will then get jammed behind the stacker plate.

Thus, we should start by power cycling the bill validator to fully reset it. Then, plug back into wall power. Remove the cash box from the valut, then insert gently yet firmly into the validator untill it clicks into place. If not, continue below. Locate two hex screws atop the plate surrounding the intake mouth of the validator. Lift up on the green tab to release the bottom half of the validator and pull towards you. The cash box and upper half of the validator should remain in the vault, but the lower portion will be removed. Open the head by pressing on the green tabs on both sides. Check for obstructions. Submit a request.

coinco bp4sx manual

Self-diagnostics communicated via status light. Manufactured and supported by Coinco. Made in the U.S.A.Only the co-signee (theWe recommendA label indicating the model number and serial number isRefer to theCoinco Service Center for information or service. TheIf the bill acceptor is being stored or used as a spare,This will keep it clean and offer the best protection forEXAMPLE: Serial number 260300135. First andThe main logic board contains the microprocessor whichFigure 1. Power RequirementsOperating Temperature. Storage Temperature. Relative HumidityPhysical Weight in Shipping CartonThe new configuration settingConfiguring the bill acceptor for bill enabling andThe anti-cheat lever is used INSTALLING THE BILL ACCEPTORThe illuminated inletNOTE: Should additional mounting hardware beLower HousingFigure 2Anti-cheat leverIf the light is. Inlet LEDs. OFF or blinking, check the following:Inlet LedsSecurity. SecurityBill Transport and Stacking. The bill transport system is composed of a motor andWhen the transport motor is energized, it pulls the bill inLeft and Right Alignment Sensors. The left and right alignment sensors send information toCenter Optic Sensor. The center optic sensor informs the microprocessor thatLeft and Right Optic Sensors. The left and right optic sensors and associated circuitryMagnetic Sensor. The magnetic sensor and its associated circuitry performs checks on the magnetic properties of the bill andAnti-Pullback Lever. The lower anti-pullback lever is optically monitored to tellStacker Home Sensor. The stacker home sensor is an optical sensor thatEncoder Sensor. Connected to the transport motor is an encoder wheelThe bill stacker is composed of a motor and gearcaseWhen the bill isComponent Explanation. Bill Box Lid. Intermediate Frame. Pusher. Plate. Stacker Home. Encoder Sensor. Pushplate. Assy. Flex Stack. Bill Box. Left-Right. Optic. Center Drive. Belt. Lower. Housing. Center Optic. Left. Alignment. Sensor. Anti-Pullback. Lever. Chassis Belt.

• coinco bp4sx manual, coinco bp4sx manual, coinco bp4sx manual, coinco bp4sx manuals, coinco bp4sx manual download, coinco bp4sx manual free, coinco bp4sx manual instructions, coinco bp4sx manual online, coinco bp4sx manual transmission, coinco bp4sx manual user, coinco bp4sx manual diagram, coinco bp4sx manual.

Operation and Service ManualSection 4: Maintenance. Introduction. 4. Models. 4. For Your Records. 4. Features. 4. After Unpacking. 4. Main Logic Board Assembly. 4. Specifications. 5. Dimensional Drawing. 5. Disassembling the BillPro. 10. Disassembling the Chassis. 13. Disassembling the Lower Housing. 15. BillPro Cleaning Maintenance Procedure. 17. Cleaning Salt Water Damage. 17. Section 2: Installation. Options Setting. 6. Setting the Configuration Options. 6. Installing the Bill Acceptor. 6. Section 3: Operation. Bill Recognition. 7. Bill Validation. 7. Bill Stacking and Credit. 7. Bill Rejection. 7. Component Explanation. Bill Transport and Stacking. 7. Left and Right Alignment Sensors. 7. Center Optic Sensor. 7. Left and Right Optic Sensor. 7. Magnetic Sensor. 7. Anti-Pullback Levers. 7. Stacker Home Sensor. 7. Encoder Sensor. 7. Component Explanation Drawing. 8. Interconnect Drawing (BP). 9. Section 5: Troubleshooting. Introduction. 18. BillPro Diagnostic Flash Codes. 18. Section 6: Parts List. Main Frame (BP). 19. Lower Housing Assembly. 21. Chassis Assembly. 23. Intermediate Frame Assembly. 24. Cashbox Assembly. 24This manual is intended for owners, route operators andTaking time to read this manual and becomingListed below areBP2BX BillPro bill acceptor, 2 bill acceptanceBP4BX BillPro bill acceptor, 4 bill acceptance. MDB interface only. BP4SX BillPro bill acceptor, 4 bill acceptance. BP2BX and BP4BX bill acceptors are primarily used inBP4SX bill acceptor are primarily used in MDB snack,BillPro units support MDB communication only.Illuminated Inlet. Flash programmable memory. Exceptional acceptance rate. Anti-jam software. Flex stack bill box. Center drive belt. Scalloped bill path for wet bill acceptance. State-of-the-art electronic logic system. Programmable acceptance of the following bills. Vandal resistant design protects against: saltwater,Utilizes standard mountingHigh impact, non-corrosive plastic construction. Easily accessible bill path.

Removing the Printed Circuit BoardUsing a small straight screwdriver, pry up at the twoPivot the front ofLift the board outRemoving the Mag Roller and SpringLift lower enclosure out of the lower housing. Figure 16Cover. Logic Board. Shroud. Lower PCB Enclosure. HousingAnti-Pullback Lever and SpringFigure 17. Using a small drift or Phillips screwdriver, depress theAt the same time, insert a small standard blade screwdriver into the center slot and push the anti-pullbackRemove the anti-pullback lever from its mount byPay close attention to theSpring. Mount. Removing the Lower Housing RollersFigure 18. Slide the front pulleys off the shaft. To remove the center belt, slide the back pulleys off theShaft. Front PulleyThe BillPro should be cleaned every 20,000 bills or everyDust can be removed with aProcedureRemove the bill box and use a soft cloth to wipe anyThe upper sensors are located directly above theRemove the bill acceptor from the vending machine. Open the bill box lid and verify that the stacker plate. If it is not in theRemove the bill box. WARNING: If moisture is present, allow the unit toIf the stacker plate does notRemove the bottom cover of the lower housing.Allow the unit to dryRemove the front mask. Using hot water and a softCAUTION: The motors are not protected from water,Allow the unit to dry thoroughly. Clean the magnetic head using a swab and isopropylReplace the front mask. Replace the lower housing cover. Place the lower housing into the main frame. Remount the bill box. Apply power and insert bills to verify the unit isFigure 19. Logic troubleshooting minimizes the time spent in removing and replacing parts that are not defective. SomePlease check the followingClean any dirt or dust from the bill path. Vending machine is not disabling unit. Connectors are inserted correctly. Connector pins are not bent or broken. All wires are properly secured.Refer to Figure 19. Flash codeThe BillPro supports the following flash codesFlash CodeCheck bill box.

Right. Alignment SensorTo. Multi-Drop. BusChangerBillPro. Main Logic BoardTerminal. Red. BlueEncoder WheelLeft Trans. and Right Skew. Right Trans. and Left Skew. Center Trans. and Center Refl. LED Anode Drive. Analog MAGStacker Motor. AssesmblyAssemblyBoard (408501)BP Figure 4Push the bill box tab forward while sliding the billFigure 5. Bill Box Tab. Figure 6. Removing the Lower HousingTo remove the lower housing, push the locking tab on theMain. Frame. Locking TabUsing a small straight tip screwdriver, free the tenFigure 7. Main Frame. Tab. Locking Tab. Detail. Removing the Inlet MaskUpper. Figure 8. Using a Phillips screwdriver, remove the three screwsMain Frame. Removing the Mounting Frame and Static. Grounding Spring (see Figure 8). Using a Phillips screwdriver, remove the screws thatStatic Ground Mounting. Spring. Nuts. Snack. Mask. Mounting. Static Ground. Bottler. MaskRemove upper PCB cover by unsnapping from front. Using a small Phillips screwdriver, remove two screwsFigure 9Upper Sensor. Board. Removing the Chassis from the Mainframe (see Figure 10). Figure 10. Remove the phillips screw securing the chassis to theCarefully feed the chassisChassisScrew. Chassis. Main FrameRemoving the Pusher Plate from the. Chassis (see Figure 11). Remove the pusher plate from the stacker gear boxPull the pusherUsing a small screwdriver,Screwdriver. Locking TabsLocking. Tabs. Stacker. Motor Cam. Board Assembly (see Figure 12). Figure 12. Remove sensor housing by tilting up and away fromAssembly. ChassisCompress the belt tensioning spring by pressing down onFigure 13. Transport Motor. Assembly. Removing the Transport and Stacker. Motor Assemblies (see Figure 14). Unplug motor wires from two connectors located onCompress the belt tensioning springFigure 14. Pulley. Transport Gearbox. Belt Tension. Transport. Slots. Stacker Gearbox. Motor. ConnectorPCB Cover. Outer Tabs.

MEI on the other hand makes it very easy to flash - either they can be flashed (flashport model) or they can't so I have one of their flashers. But there is never any concern of whether they need and eprom or a logic board because that can never be done on MEIs. It can be programmed for bills up to 20s The anti-cheat lever is used to enter configuration programming mode, scroll through all possible configuration options and select the required configuration. The illuminated inlet provides feedback to the user during the configuration process by displaying a pattern that corresponds to each configuration option available Is it a plug and play replacement? Thanks Heading to machine shortly good timing lol I haven't tried programming my machine yet it is a identical Dba. The BillPro (not what you have) is the next generation to the MAG32 and it will generally take 5's or more without an update. Otherwise, I would advise you to get a Mars 2512 that accept new 5's. In the future I'll definitely switch to all Mars when it craps out I'm slowly getting away from coinco stuff. That way I can flash my BP4SX without taking the snack machine out of service. I wanted to also take a quarter tube out and add a dollar tube. I have a coinco mdb coin mech I took out of a Dixie 276e that I'll use as a spare. Because of the cost to those last two items you can't assume that a repair will include the software update. It's easy! Sign in here. Both my coin acceptor and bill acceptor were powered off. I've had the bill acceptor do this before when it had a jammed dollar bill in it in the recycler unit.I took all the dollar bills out of the recycler part and main holder, and then turned the machine back on. However the front bezel part wouldn't light up, and it wouldn't accept bills. So I don't know if that's what messed everything up. I'll call coinco tomorrow, but I'm lost. This is for my Vendever Cotton Candy Machine.

Return for service. NOTE: A scrolling light, in the illuminatedIf all LEDsBottler Mask. Security Bottler Mask. Snack Mask. Screw. Mounting Frame, Bottler. Mounting Frame, Snack. Grounding Spring. BillPro Front Label. BillPro Front LabelBottler. SnackLogic PCB Assy. Anti-Pullback Light Pipe Shroud. Lower Enclosure. Anti-Pullback Lever Spring. Anti-Pullback Lever Mount. Anti-Pullback Lever. Center Belt. Idler Roller. Drive Shaft. Sensor Plug. Cable Tie. MDB Cable Assy. ID LabelEncoder Wheel. Stacker Pushplate Assy. BillPro. Stacker Cap. Stacker Slide. Belt Tension Spring. Stacker Motor Gearbox Assy. Idler Pulley. Chassis With Connectors. Upper Housing Chassis. Upper Sensor Cover. Upper Sensor Board. Maghead gasket. Sensor Mount. Upper Sensor Enclosure. Wheel Shaft. HarnessIncludes 925234 with connectors. Without connectorsSt. Louis, MO 63124-2013Coinco Publication No. 925495 Rev.1. See why thousands are coming to eBid. Ship validators to: How do I pay? I mistakenly bought 2. Can you please fix to one so I can pay. I am shipping thus today. Thank you. I already shipped item to you. Thanks I purchased from you because of your reputation. Im not sure what happened here. Thanks anyway. Something went wrong. This is a great product from Coinco, a world leader in automatic point of sale products. Cancel Thanks, we'll look into this. All Rights Reserved. User Agreement, Privacy, Cookies and AdChoice Norton Secured - powered by Verisign. There you'll see a set of 8 dip switches. If it doesn't then yours is not updated for the new currency. You can email me at rbepic4gatgmaildotcom if you need an upgraded unit. Some just need a software flash, some need an eprom and some need a logic board upgrade. The flash requires a hand held programmer that is expensive to buy unless you are updating many validators. I never found it cost effective to have a Coinco programmer as the number of units I encountered that only needed a flash is small.

If there is actual damage to the coin mech's lever, then you will need to replace the coin mech.The change option may have been turned off to prevent people from using your machine as a changer, but you might increase sales with the acceptance of 5's. When I took off the coin return, that little plastic tab was broken off and the coin side was stuck open. Doing exactly what AZvendor said might be going on. Causing a constant signal to be sent. I also tried turning on the machine at location without the coin acceptor plugged in, any variation I could think of I tried, and it never worked and always had the same problem. There's a display that's suppose to show how many credits hav been imputed (0 when just starting up) and you're suppose to be able to change the price using it. I followed the price change instructions, and it would never even light up. The machine I just put out doesn't have a VMC box like the other one (even though they ware made by the same company, same month, same year), so I couldn't just switch VMC boxes.What I found was, if I wiggled the VMC, it would turn on for a SPLIT second, and light up the display board to something funky. That spark happened the exact split second the board would light up. I'm guessing the singe fried something else and a new board will make it work fine? I would imagine it is doing pretty well in the movie theater. Any idea why it completely shuts down after accepting 2 dollars? Specific model: MagPro R series. Thank Any idea why it completely shuts down after accepting 2 dollars? Specific model: MagPro R series. Thank Make sure you have sufficient change in the coin tubes to continue accepting bills. If you pay out change from the first two bills and the coin level drops below the tube sensor then the validator can be inhibited. If you're using this on an MDB machine then you may need to use the Tube Fill part of your programming to properly count coins into your coin mech.

This ensures the machine knows it has enough coins for change making. It's easy! Sign in here. The item includes accessories found with the original product and may include a warranty. See the seller's listing for full details and description. View cart for details. Please note that most of my stuff comes from government auctions. It is rare that an owner's manual makes it to the auction. All items sold are as listed, so please bid accordingly. Misc.electronics takes all auctions very serious, and will make all attempts to provide accurate information on each item listed. We try our best to test all equipment. Some items we will not have the equipment, facilities or knowledge to do so. Shipping charges are for the lower 48 United States only, We ship with the Post Office or UPS depending on the weight of the package. All items are shipped insured. Due to the large volume of sales that we have, we have adopted a feedback policy that seems to work for both us and our customers. On a regular basis, we go through our feedback file and submit feedback for all of those who have filed feedback on us. This policy ensures that everyone gets proper recognition and makes the process a bit smoother for both parties. If you are satisfied with your transaction with us, please leave your comment on our file and we will be sure to reciprocate when we do our daily updates. Before posting negative feedback please contact us so we can work it out.Get Vendio Sales Manager. FREE scheduling, supersized images and templates. Get Vendio Sales Manager. Over 100,000,000 served. Get FREE counters from Vendio today! With a 30 day warranty., MPN: BP4SX, Brand: coinco, Model: BP4SX Super high amount of views. 1 sold, 0 available. More Super high amount of views. 1 sold, 0 available. You are the light of the world.

coin mech repair manual

This indicates that the coin changer is in float mode, to toggle this mode press and release inventory buttons A and D simultaneously followed by buttons B and C simultaneously. What is the Coin Float Mode. The ability to maintain coin levels in the coin mech is called the coin float mode. The Quantum and Global coin mechs have two types of float available, the paydown float and the level float. The coin mechs are sold with paydown float ON as default. Paydown float mode will allow the coin tubes to fill to full and later they can be paid down to the set coin levels, therefore maintaining a set change level after a service call. Level Float mode will cause the coin tubes to fill to the set level after which all additional coins will be routed to the cashbox, therefore maintaining a set change level throughout operation. To change the float mode type, the coin mech needs to be returned to a service centre, so it can changed via software. This will be done at no cost. After this, when the coin mech is in the machine, it needs to have coins fed into it so it can have an accurate coin count for each tube. This is done via the TUBE FILL mode in an electronic vending machine or via the coin mech's manual fill mode in electromechanical vending machines. See the manual for full float mode details. How do I set the vend price. Setting The Vend Prices. If the Vending machine is fitted with its own electronic control board the prices are set through its menu. Otherwise if the coin mech is either an ALQ-F70X or ALD-F70X and is connected to the vending machine via the black Jones plug, then it is the only price control in the vending machine, the prices are set with the series of switches that are behind the acceptor head, the beige part at the top, there is a latch at the top right corner that allows the acceptor head to folded forward to reveal the switches.

• coin mech repair manual, coin mech repair manual pdf, coin mech repair manual download, coin mech repair manual online, coin mech repair manual free.

You must have JavaScript enabled in your browser to utilize the functionality of this website. All company trademarks and logos used on this site are property of their respective owners, and all of the companies rights are reserved. Monster Vending has no affiliation with any of these companies nor do we represent or are distributors of these companies in any way. Trademarks and logos are ONLY used for display purposes. Monster Vending is not affiliated with Automatic Products, National Vendors, Coca Cola, CCE, Pepsi,or PBG in any way and simply sells their equipment in refurbished condition. All prices are in US dollars. Prices subject to change without notice. We are not bound by or liable for typographical errors on this site, regarding prices, inaccurate pictures, or other mistakes. Please see legal notices about this site. Please see copyright information page for copyright information. Superseded by the Guardian 6000 coin mech. Key Features: Four payout coin tubes for more changemaking and greater vending sales. Simple modular design for easy servicing. 2 year warranty. Built in programmable payout feature. Space for 16 coins or tokens to be accepted. No, it has been superseded by the Guardian 6000 XL Coin Changer. The Global 2 units have run out and no more will be available. How do I send my faulty coin mech in for service and what will it cost. When sending in your coin mechs for service include your company name and contact details (name and phone number). Ensure a street (not postal address) is included in your details as we will return it via TNT couriers. Otherwise, delivery via Australia post may result in delays due to processing time. Also include a description of the fault, as this will help us complete your repairs sooner and allow us to service the mech in case we find no fault. Return freight will also be charged. Why is the LED on the front of the acceptor flashing.

Check there are no coins in there and that the sensor lens and mirror are clean. Coins can become jammed in there if the cashbox fills all the way up into the coin mech, or if the coins get caught as they are coming out of the coin mech. Check that there is nothing to catch the coin as it falls from the coin mech to the cashbox. How should I clean the product. Use a damp Cloth to clean surface dirt, any persistant grime can be cleaned off using a gentle cleaner, that will not leave a residue. (we recommend Windex). Ensure the product is dry after cleaning. When cleaning a Global or Quantum coin changer the following areas are particularly important. For Assistance and Parts Call or Write. PO Box 1127 Shiner, Texas 77984Quick Change Lockout in the position below is for Daily papers. To change to Sunday, insertNOTE: After changing from Daily to Sunday or from Sunday to Daily, be sure to push in Coin. Return Button to set Mechanism.DO NOT loosen nut. Each hole in quarterIf using a (T-849) Wheel “0” is. Setters as needed. When changing the (T-844), make sure (T-843) does not move from itsDrawing shows proper position of Parts T-814, T-818 and T-823.Also, T-818 must fit Snug and Square in One tooth. Positions otherEach tooth represents “1” Nickel, starting at “0” Nickels through “23” Nickels (For Price Wheel T815). When a Quarter is inserted,When the rack door is open the Ratchet Pawl (T-818) should lift away from the Wheel allowingThe Rocker Arm Reset Link (T836) controls this.If the T-818 is not fitting Snug and Square in One. Tooth of T-814 as shown on Page 4, the wheel mayON DAILY: Take one or both Price Setters and putPlate (T-811). Push Coin Reject Button. This willScrewdrivers to push in direction of solid arrows. Check to see if T-818 is seated in Tooth properly byIf not, exert force with. Two Screwdriver as shown by dashing arrows. Check again by pushing Reject Button. MovementT-818 properly. NOTE: Excessive force will loosenPrice Setting.

There are two types of price setting, single and four price, this is dependant on the actual switch wiring with in the vending machine, it can either be wired for a single price or wired for up to four prices. The type of price setting is indicated in the coin mech by switch 10. If it is OFF then it is set as a single price coin mech, and conversely if it is ON it is set as a four price coin mech (even if there is only a single price for all four price lines.) The use of either single or four price setting is wholly dependant on the vending machine. It will turn off momentarily, then return to a steady on. The LED will start to flash, now press the selection on the vending machine you want that price set to. Repeat this process with every selection on the vending machine (to ensure that a price is set for all selections). What are the posible coin tube configurations for the Quantum coin mech. The following is a list of the Australian coins, the tube used for the coin and the possible locations in the cassette for that tube. What is the default coin tube configuration for the Quantum coin mech. What is the difference between the non-programmable and programmable Global changer. With a programmable changer the operator is able to change the coin routing in the field. A programmable changer will have a grey 25mm wide gate cable (front top right corner) whereas the nonprogrammable changer has a white or golden 14mm wide cable. Why doesn't the coin mech accept any coins to the cashbox. This fault indicates that the coin mech is not accepting cashbox coins, that is coins that are destined to be routed to the cashbox. (This is easily tested by checking if a 5c coin is accepted). The most common cause of this fault is a blocked cashbox sensor therefore the coin mech believes that the cashbox is full and will not accept any further cashbox coins. The cashbox sensor can be checked by removing the cashbox shute cover on the rear of the coin mech.

NOTE: Totalizer Arm (T-822) must be parallel and flush with edge of Plate (T-803) to workIf the Totalizer Arm (T-822) is bent or theThe following are the most common problems ofBase Swing Plate (T-801). The Base Swing Plate (T801) should rest against heads of bolts that fasten. Coin Guide Plate (T-803) to TK Chassis. If T-801Check CleaningCheck Cleaning and General Care. Instructions.Totalizer Arm is bent too far in or too far back. See. Figure 3 for proper position.Plate (T-801) causing a mistotal. See Figure 1. BothCoins will not be totaled properly if Latch Release (T-820) is resting against Price Range Wheel (T-815),Loosen nuts on Door Hook and move down till. Latch Release moves away from Price Range Wheel. CAUTION: If Hook is too low, door will openThe Illustration above on the right, shows TK-Mech mounted in Housing and sitting on rack. For clarity. Base, Swing and Coin Guide Plates are shown missing. Also, Side Mounting Plate (T-807) is not shown. Side Mounting Plate must be installed for Coin Return Door (T-808) and Coin Receiver Door (T-809) toIf T-809 goes beyond Stop, moneyReplace Coin Receiver Door (T-809). Check Door Adjustments with rack and door latch bracket fitting properly against Housing front. Notice if. Door Pull has pushed in Housing. This causes Door Hook not to release and coins cannot be rejected. Take TK-Mech out of Sho-Rack and straighten TK Chassis and Mech Housing. Check for bent Door. Hook (T-847) and straighten with pliers if needed. Also check for bent Latch (T-825). Also make sure. Door Hook (T-847) comes into the rack hitting fairly centered on the rollers of the Latch (T-825) and the. Rocker Arm (T-835).To make adjustment, bend the T-820 tab with TOOL A (6049) asRelease (T-820) is touching the Wheel (T-814) coins will not total. Hook (T847) not being adjusted properly. Make sure Door Hook and Door are in proper. Refer to Page 10 for Door and Door Hook. Adjustments. Wheel.

ON SUNDAY: Check Daily Setting first beforeIf Sunday does notIf not, apply pressure andPush Reject ButtonContinual use of the TK-Mech will sometimes causeSprings on Drawing to left. Stacked means loops of. Spring intertwined causing Index Wheel to stopTo solve this, move. Spring to far left as shown in Drawing or to far right. DO NOT remove or unhook Spring.Rocker Arm (T-835) moves to Stop on T-800 (Follow Arrows) that may get bent up or downPosition of Stop should be asPrice Setting. If too far Down, the paper compartment door will not close. Bend with pliers toCheck for proper space between T-820 and T-815. See Illustration on Page 10 for correctFigure 1. Figure 2: The T-835 (Rocker Arm) binding with the T-825 (Latch) can keep the rack door fromFigure 3: The T-837 (Actuator Arm) has been removed for better clarity to show the lubricationCoins will not reject properly if the Coin Return Bar (T-824) is bent. This happens whenFigure 1 shows the Coin Return Bar (T-824) straight and in its proper position, shown by. Shaded Area. The DOTTED LINE on Figure 1, shows the Actuator Bar (T-837) pushing up onThis happens when the Coin Return Bar (T-824) gets bentTo correct, look at the Illustration in Figure 2,Some parts have been removed for better visibility. Make sure the T-824 isThe Coin Return Bar (T-824) should fit flush against the front hole where the Coin Return ButtonBoth figures show the front of the TK Chassis being bent from the Rack falling over. The. Chassis can be hammered back out to fit into the Rack. Sometimes the Chassis will beLine in Figure 1) and touch side of slots in Base and Swing Plates. Coins will not fall andLines in Drawing. Also, Coin Guide Plate Coin Guides must be centered in slots to allow proper coin drop to. Totalizer Arm. These Coin Guides also should be bent with pliers to proper position as shownArrows.

Older Guardian 6000 coin mechanism have a shallower (15 degrees) rail, identified by the circular hole in the rail. The new rail is steeper (20 degrees) and is identified by the rounded square hole in it. If you have any Guardian 6000 coin mech with the older rail, please contact us and we will send you some to swap over. Q.Does my Guardian 6000 coin mechanism need a software upgrade? A.The current stable software version is 2.11. You can view the coin mechanism software version during startup; it will be displayed briefly after the Guardian 6000 screen, below the model number on the next screen. Earlier software version may have issues with coin routing, poor full tube payout and tube counts. If your coin mech has an earlier software version it needs to be sent in for service, this is a warranty upgrade service. Q.How do I enable 5 cent coin acceptance? A.To get the Guardian coin mechanism to accept 5c coins, the scaling factor needs to be changed, by default it is set to 10. It needs to be set to 5 so it can accept the 5c coin, to do this enter the Guardian menu system by pressing the menu button. The display will show Main Menu Audit, press the down arrow ?B? button to get to Setup, press Enter ?C? button the display will now show ?Setup Float?, press the up arrow ?E? twice to get to General, press Enter. The display will show General Autotest, press the down arrow ?B? button to get to MDB Settings, press Enter ?C? button. The display will now show MDB Level, press the down arrow ?B? button to get to Scale Factor, press Enter ?C? button. The display will now show Scale Factor 10, press the down arrow ?B? button five times to get to Scale Factor 5, press Enter ?C? button the display will now return to the default display. A?The following is a list of the Australian coins, the tube used for the coin and the possible locations in the cassette for that tube.

The Guardian 6000 coin mech has two types of float available, the float pay down and the level float, either mode can be set via the display menu system. Float pay down mode will allow the coin tubes to fill to full and later they can be paid down to the set coin levels, therefore maintaining a set change level after a service call. Level Float mode will cause the coin tubes to fill to the set level after which all additional coins will be routed to the cashbox, therefore maintaining a set change level throughout operation. This will not stop the normal operation of the Guardian 6000. Check fuse and transformer. Test acceptance. If it accepts, replug each connection one at a time and test acceptance after each. If found to be defective, replace the harness. If vender won't pay out using the CPO mode or during sales, check harness for cuts, bad continuity, or wrong connections. If defective, replace and test. If it pays out, the coin mech was defective. If not, check acceptor harnessing or replace the bill acceptor. Repair or replace if necessary. If acceptor pull bill in, acceptor was defective. NOTE: if the sensor is not present or is cut (defective), the controller will allow up to two products from each column assigned to be vended begore the column is determined to be sold out. Make sure the only time the light comes on is when a product hits the can chute. If not replace the vend motor. Dry vend (no refund). If so, adjust it back to factory setting.Watch the LED. If the adjusment LED goes out, replace the defective sensor. Reinsert the fuse. If the adjustment LED immediately lights up, turn the screw counterclockwise to see if the light goes out. If not, replace the control board. Trace the selection harness back to the control board. Replace if necessary. Measure it on the individual wire for the motor attempted and the wire itself next to the key (neutral). If not, replace the control board. Check space-to-sales settings; reprogram if necessary.

Use a Tailbender, TOOL B (6025) on the T-820 tab where the T835 tab connects ontoSoaking time depends on the amountDawn Dishwashing Liquid is good to use for washing your Mechs. Rinse your Mechs thoroughly and then it is best to blow-dry them. Make sure to reoil all studsIf putting in a dishwasher and you have the T779 (Protection Baffle) in the Mech, remove the. T812 (Side Cover Plate) and T811 (Top Cover Plate) and run through a full cycle. Reoil studs. If your Mech does not have the T779 (Protection Baffle), we recommend the following parts beLock Assembly, T801-T802 (Swing Plate Assembly), the Wheel Assembly and T822-T823Reoil studs. If using an all purpose degreaser spray, wash your Mechs in hot water, rinse in hot water andAfter cleaning the Mechs, if the TOTALIZER ARM and the WHEEL are STILL SLUGGISH, youAny defective parts should be replaced at this time and all minor adjustments made. Usually aMost of the problems of a Mech not totalingMech will mistotal. Amsoil 100% Synthetic 5W-30 Motor Oil (Winterlube Oil) should be used.Applications of Lubriplate 105 anmd Door Ease or equivalent. The following legend denotesLook for these letter symbols on TK-Mech. Some machines feature an LED indicator that identifies problems, such as a jammed or bent coin or dirty sensor. The LED is typically located on the keypad and puts out a series of flashes that correspond to a specific malfunction. Some units flash twice when a coin is jammed, while others flash three or four times to indicate that the machine needs cleaning -- a dirty sensor will not function correctly and lead to more complicated errors if not addressed immediately. Refer to your owner's manual for your LED indicator's diagnostic programming. 1 Remove the power from the coin changer before performing repairs. If a strobe sensor is obstructed, remove the cassette at the back of the machine by loosening the screw with a screwdriver. The screws should be above the acceptor tray.

Loosen it just enough to tilt the tray forward. 2 Lift up the tray or slot and set aside. Disconnect the colored ribbon connector, usually gray, and turn over the assembly unit to locate the second ribbon connector, if your machine has one. Identify the color-coded cables inserted on either side of the second ribbon connector and detach from the back of the unit by pulling them out of their casings. Pull them straight out, not at an angle. 3 Unwind the ribbon and cables to remove the separator unit from the acceptor tray or slot. Identify the clips, usually on the left-hand side of the acceptor, to unhinge the separator from the front of the acceptor. 4 Access the coin-acceptor slot once the separator is completely removed and set aside. The sensor that indicates a jam is typically located above the slot opening. Remove any dirt or debris with a clean cloth or dislodge coins stuck in this opening. 5 Reroute the cables and ribbons and reassemble the coin changer. Plug in the unit. The LED diagnostic indicator light should be solid or unlit if the obstruction has been successfully cleared. Refer to your owner's manual for specific LED diagnostics. Trained as a journalist, she has traveled to over 150 US cities. She specializes in travel, culture, pets, business and social networking and regularly publishes in newspapers, magazines and on Web sites. She received a Bachelor of Arts in writing from the College of Santa Fe. If no coins are present in the tubes the sonar readings will be from reflections from outside the coin mechanism giving incorrect coin counts. Therefore it is important to initially hand fill each tube with five coins. Q?Does my Guardian 6000 coin mech need a new steeper coin rail? A.The metal coin rail sits in the acceptor gate path, where the coin first enter the acceptor. Its function is to debounce the coin so reliable readings can by taken by the coin mechanism sensors.

If not, check for voltage (5 VDC) with a voltmeter at the door switch. If not, check for voltage (5 VDC) at the door switch's pinout on the control board. If no voltage is found there, replace the control board. Also, check for bad connections. If no voltage is found, replace the control board. Secondary power harness to the transformer. Lights defective. Replace secondary power harness. Check power with voltmeter from transformer to control board. Replace if necessary. Replace if necessary. Replace if necessary. If the 8's remain, replace the control board. Replace whatever causes the 8's to appear. Wait approximately 20 seconds for the board to reset. Reprogram the control board. If the problem reappears or the board cannot be reprogrammed, replace the control board. If you own, restore, or service vintage soda machines, you are in the right place. Be sure to check back often, since new features and products are added frequently! Our reprinted Service Manuals are on quality paper that resists fading. Discard these separately. The globe will then lift free off the hopper. The interior of the machine should ONLY BE CLEANED USING FOOD GRADE PRODUCTS. A dry cloth is recommended for cleaning the interior of the globe. This hub acts as a bearing for the various dispensing wheels and must have lubrication at all times. All service head components can be washed in warm water with dish soap. They include the following items: This will make future removal much easier. This procedure will help ensure a smooth operation as well as help reduce wear on the various working components, extending service life. The slip clutch handle is a maintenance free component. It has permanently lubricated bearings inside which do not require re-lubrication unless the handle is disassembled. Every 6 months apply a drop of thin multipurpose oil (such as sewing machine oil) into the top opening of the lock, then insert the key, lock.

This procedure will help in keeping the locks operating smoothly, as well as reducing the wear over time. Unscented alcohol-based wipes are also suitable. For more information about cleaning and where to purchase suitable cleaning materials, contact your local Environmental Health Office. If for any reason wet cleaning cannot be avoided, then it is vital that the machine is completely dry before being reassembled and refilled. A minimum of 24 hours drying time is recommended to ensure all moisture is evaporated. Be sure to remove any stale product and thoroughly clean the corners before refilling the machine.